JH Technology JH5000, 5030, 5060 & 5070 series Signal Conditioners

JH5000: DC Voltage Inputs, 1V or Greater
JH5030: DC 4/20mA or Current Input
JH5060: DC Current Inputs (except 4/20mA)
JH5070: DC Millivolt Inputs, less than 1V

JH5000 Series DIN-Rail Transmitters provide an isolated DC output proportional to a DC voltage or current input. The model numbers listed above reflect a variety of input choices but all share the same basic circuitry, features and specifications. This page covers fixed-range devices, precisely calibrated to your range at the factory. A user-rangeable transmitter is available: see Model JH5080.

Red-green Quick-Check LEDs give a quick indication of the relative output. Red is brighter at the low end, green at high, while at mid-scale both are approximately equal. Red-only indicates offscale low while green-only indicates offscale high.

Model JH5070 incorporates a low-drift input amplifier for millivolt-level inputs. All models use stable, proven circuitry for accurate measurements under varying ambient conditions. Available options include AC and DC power choices and reverse-acting transmitter (decreasing output with increasing input).

ORDERING INFORMATION

Model Number: Select from the list above according to your input range. Add suffix A (for example, JH5000A) for AC power, D for DC power.

Input Range: Specify any DC voltage or current range allowed by the "Input Capabilities" spec, below.

Output Range:
Specify any DC voltage or current range allowed by the "Output Capabilities" spec, below.

Power:
Specify 115Vac, 230Vac, 12Vdc or 24Vdc.

Reverse-Acting Transmitter
(decreasing output with increasing input):
Change last digit of the model number to 1 (for example, JH5001A).

Loop-Powered Output:
4/20mA "current sink" output stage for connection to devices whose inputs provide 24Vdc loop excitation. Change the last digit of the model number to 2 (for example, JH5002A).

Urethane Coating:
Specify Option U.

JH5000 Series transmitters snap onto 35mm DIN rail. Connections are made to the front-panel terminals. The terminal strip unplugs to facilitate calibrating or replacing the transmitter.

Connections to the 8 terminals (top to bottom) are:
    1: Input plus.
    2: Input minus.
    3: No connection.
    4: No connection.
    5: Output plus.
    6: Output minus.
    7: Power (AC or, if DC power option, DC plus).
    8: Power (AC or, if DC power option, DC minus).

Input Capabilities, Model JH5000:	1V minimum span, +/-250V maximum input. Offset ranges are allowed. (Input Impedance: 200kohms or greater.)
Input Range, Model JH5030:	4/20mAdc. (62 ohms input resistance - 1.25V drop at full scale.)
Input Capabilities, Model JH5060:	1mA minimum span, +/-5 Amps maximum input. Offset ranges are allowed. (Input voltage drop typically 0.1V at full scale.)
Input Capabilities, Model JH5070:	4mV minimum span, 1V maximum span (specify JH5000 for spans greater than 1V.) Offset ranges are allowed. (Input Impedance: 200kohms or greater.)
Voltage Output Capabilities:	1 volt minimum output span, -10 to +15V absolute limit. Offset ranges are allowed. Maximum output load, 10mA (1Kohm at 10V output).
Current Output Capabilities:	1mA minimum output span, 0 to +25mA absolute limit. Positive offsets are allowed, negative outputs are not. Output drive capability, 24V (1,200 ohms max. at 20mA output).
Accuracy (factory calibration):	+/-0.1% of span or 10 microvolts, whichever is greater.
Adjustability:	Zero and span each are adjustable approx. +/-15% of span.
Linearity:	+/-0.05% of span or better.
Response Time:	Under 100 milliseconds.
Isolation:	3-way (Power/Input/Output) 1,500Vac rms (2,100V peak).
Guaranteed Operating Temperature:	-10 to +60 deg. C (14 to 140 deg. F).
Temperature Stability:	+/-(0.02% of span plus 1.3 microvolts) per deg. C, or better.
Power Requirements:	AC, 115 or 230Vrms, 50/60Hz, 2.5V-A. DC, 12 or 24V, 2.5W.