|
JH5400: 100 Ohm Platinum RTD, Linearized
-
Available
for all RTD Types
-
Linearizes
Platinum RTDs
-
3-Wire
Lead Compensation Standard
(4-wire available)
-
DIN-Rail
Mount, 1 Inch Wide
-
Unpluggable
Terminal Strip
-
AC
or DC Power Options
|
|
JH5400 Series RTD Input Transmitters provide an isolated DC
output proportional to temperature as measured by a resistance
thermometer (RTD). Model JH5400 specifically designates 100 ohm
platinum RTD input: additional model numbers are reserved for other
RTD types.
Standard three-wire input circuitry compensates for lead wire
resistance. A 4-wire input option is available. Platinum RTDs are
linearized to provide true temperature indication. (Other types may
or may not be: contact us to discuss your specific requirements.) A
low-drift input amplifier helps assure accurate readings under
varying ambient conditions.
Red-green Quick-Check LEDs give a quick indication of the
relative output. Red is brighter at the low end, green at high,
while at mid-scale both are approximately equal. Red-only indicates
offscale low while green-only indicates offscale high.
Available options include AC and DC power choices and
reverse-acting transmitter (decreasing output with increasing
input).
ORDERING INFORMATION
| Model
Number: |
Specify Model
JH5400 for use with 100 ohm platinum RTDs. Other model
numbers will be assigned for other RTD types. Add suffix A
(for example, JH5400A) for AC power, D for DC power. |
| RTD
Type: |
Determined by
model number |
| Input
Range: |
Specify any
input range allowed by the "Input Capabilities"
spec, below. |
| Output
Range: |
Specify any DC voltage or current range allowed by the
"Output Capabilities" spec, below.
|
| 4-Wire
RTD Input: |
Specify Option 4W |
| Power:
|
Specify 115Vac, 230Vac, 12Vdc or 24Vdc.
|
Reverse-Acting
Transmitter
(decreasing output with increasing input): |
Change last digit of the model number to 1 (for example,
JH5401A).
|
| Loop-Powered
Output: |
4/20mA "current sink" output stage for
connection to devices whose inputs provide 24Vdc loop
excitation. Change the last digit of the model number to 2
(for example, JH5402A).
|
| Urethane
Coating: |
Specify Option U.
|
INSTALLATION AND CONNECTIONS
JH5400 Series transmitters snap onto 35mm DIN
rail. Connections are made to the front-panel terminals. The
terminal strip unplugs to facilitate calibrating or replacing the
transmitter.
Connections to the 8 terminals (top to bottom)
are:
1: RTD.
2: RTD compensation (same end of RTD as
terminal 1).
3: RTD (opposite end)
4: No connection - Standard or 4th RTD
wire w/option 4W.
5: Output plus.
6: Output minus.
7: Power (AC or, if DC power option, DC
plus).
8: Power (AC or, if DC power option, DC
minus).
DETAILED SPECIFICATIONS
|
RTD Type:
|
Any RTD from
10 to 2,000 ohms. (Model JH5400 for 100 ohm platinum,
other models JH54x0 for other types. Contact factory.
Specify RTD type, resistance & slope.) |
| Input
Capabilities: |
Minimum span
10 deg. C (18 deg. F) or 1 ohm, whichever is greater.
Maximum range will cover any RTD's full temperature range. |
|
Voltage
Output Capabilities:
|
1 volt minimum output span, -10 to
+15V absolute limit. Offset ranges are allowed. Maximum
output load, 10mA (1Kohm at 10V output).
|
|
Current
Output Capabilities:
|
1mA minimum output span, 0 to +25mA
absolute limit. Positive offsets are allowed, negative
outputs are not. Output drive capability, 24V (1,200 ohms
max. at 20mA output).
|
|
Accuracy:
|
+/-0.1% of span or 0.02 ohms,
whichever is greater.
|
| Adjustability: |
Zero and span
each are adjustable approx. +/-15% of span. |
|
Linearity:
|
Platinum RTDs are linearized. Copper
is inherently linear. Contact factory for information on
others.
|
|
Response
Time:
|
Under 100 milliseconds.
|
|
Isolation:
|
3-way (Power/Input/Output) 1,500Vac
rms (2,100V peak).
|
|
Guaranteed
Operating Temperature:
|
-10 to +60 deg. C (14 to 140 deg. F).
|
|
Temperature
Stability:
|
+/-(0.02% of span) per deg. C, or
better.
|
|
Power
Requirements:
|
AC, 115 or 230Vrms, 50/60Hz, 2.5V-A.
DC, 12 or 24V, 2.5W.
|
|
